point-to-point
Backbone area 0
Broadcast multicast
Non-broadcast multi-access
The DR/BDR process is done for all interface types
第1题:
A.1
B.10
C.1562
D.64000
E.128000
第2题:
A. point-to-point
B. Backbone area 0
C. Broadcast multicast
D. Non-broadcast multi-access
E. The DR/BDR process is done for all interface types
第3题:
Refer to the exhibit. The routing protocols EIGRP and OSPF have been configured as indicated in the exhibit. Given the partial configuration of router R2, which network will be present in th e routing table of R4?()
A. Network B
B. Network A and Network B
C. Network A
D. neither Network A nor Network B
第4题:
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?()
A. one
B. three
C. two
D. zero
第5题:
A. Ensure that an interface has been configured with an IP address
B. Ensure that IP classless is enabled
C. Ensure that the interfaces can ping their directly connected neighbors
D. Ensure that an interface has been configured with an IP address and is up
第6题:
A.The NProuter has two OSPF neighbors in the "Full" adjacency state
B.The NProuter serial0/0 interface has the OSPF dead timer set to 10 seconds
C.The NProuter serial0/0 interface has been configured with an OSPF network type of "pointtopoint"
D.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers setting
E.The "Mismatched" error is caus ed by the expiration of the OSPF timers
第7题:
A.90
B.100
C.110
D.120
E.130
F.170
G.200
第8题:
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?()
A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast
B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point
C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3
D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
第9题:
OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? ()
A. The ip ospf network broadcast command should be configured on each Frame Relay interface
B. The ip ospf network non -broadcast command should be configured on each Frame Relay interface
C. Th e ip ospf priority value on the spoke routers should be set to 0
D. The ip ospf priority value on the hub router should be set to 0
E. The neighbor command should be configured under the OSPF routing process on all routers
第10题:
Acme Costume Company is connecting its manufacturing facilties to its stores with a small pointto-multipoint Frame Relay IP WAN. Little growth is expected in the network infrastructure.Up to this point the company has been using a dial-on-demand network. Dropping WAN costs, however, have led them to consider using a high-speed WAN solution to improve access. Which two routing protocols could you deploy to support the new larger network while keeping costs down?()