The main factor which determines the output of each cylinder

Because the timing of injection is crucial, _____ mounted on the camshaft, which is driven by the crankshaft are used to operate the fuel pumps, one of which is provided for each cylinder.

A.gears

B.rams

C.barrels

D.cams

Which devices are instruments of interpretation and communication between humans and computers?

A．main memory

B．input/output devices

C．CPU

D．hard disk

Object-oriented analysis(OOA)is a semiformal specification technique for the object-oriented paradigm. Object-oriented analysis consists of three steps. The first step is(71). It determines how the various results are computed by the product and presents this information in the form. of a(72)and associated scenarios. The second is(73), which determines the classes and their attributes. Then determine the interrelationships and interaction among the classes. The last step is(74), which determines the actions performed by or to each class or subclass and presents this information in the form. of(75).

A．use-case modeling

B．class modeling

C．dynamic modeling

D．behavioral modeling

第一组： The Wartsila 50DF operates on the lean-bum principle: the mixture of air and gas in the cylinder has more air than is needed for complete combustion. Lean combustion reduces peak temperatures and therefore NOx emissions. Efficiency is increased and higher output is reached while avoiding knocking. Combustion of the lean air-fuel mixture is initiated by injecting a small amount of LFO (pilot fuel) into the cylinder. The pilot fuel is ignited in a conventional diesel process, providing a high-energy ignition source for the main engine. To obtain the best efficiency and lowest emissions, every cylinder is individually controlled to ensure operation at the correct air-fuel ratio and with the correct amount and timing of pilot fuel rejection. Wartsila has developed a special electronic control system to cope with the demanding task of controlling the combustion in each cylinder, and to ensure optimal performance in terms of efficiency and emissions under all conditions by keeping each cylinder within the operating window. Stable and well-controlled combustion also contributes to less mechanical and thermal load on the engine components. Current stringent emission regulations demand the reduction of NOx emissions. In an internal combustion engine this means controlling peak temperature and residence time, which are the main parameters governing NOx formations. In the Wartsila 50DF engine, the air-fuel ratio is very high (typically 2.2). Since the same specific heat quantity released by combustion is used to heat up a larger mass of air, the maximum temperature and consequently NOx formation are lower. The mixture is uniform. throughout the cylinder since the fuel and air are premixed before introduction into the cylinders, which helps to avoid local NOx formation points within the cylinder. Benefiting from this unique feature, NOx emissions from the Wartsila 50DF are extremely and comply with the most stringent existing legislation.

What is the combustion feature of the Wartsila 50DF?

A.Lean air in the cylinder

B.Excessive fuel in the cylinder

C.Excessive air in the cylinder

D.Spark ignition

Object-oriented analysis (OOA) is a semiformal specification technique for the object-oriented paradigm. Object-oriented analysis consists of three steps. The first step is(71) . It determines how the various results are computed by the product and presents this information in the form. of a(72) and associated scenarios. The second is(73) , which determines the classes and their attributes, then determines the interrelationships and interaction among the classes. The last step is(74) , which determines the actions performed by or to each class or subclass and presents this information in the form. of (75) .

A．static modeling

B．dynamic modeling

C．use-case modeling

D．behavioral modeling

Which factor determines the ring dam size for a fuel oil, tubular bowl type, centrifugal purifier?

A.The viscosity of the fuel.

B.The quantity of water to be removed from the fuel.

C.The specific gravity of the fuel.

D.The quantity of dirt to be removed from the fuel.

Each cylinder is closed at the top by a _____, made of a special heat-resistant steel.

A.cylinder liner

B.coupling flange

C.cylinder cover

D.piston crown

The main factor which determines the output of each cylinder is _____.

A.the cylinder weight

B.the cylinder bore

C.the cylinder length

D.the cylinder cover