You issue the ping interface t1-1/1/0 bypass-routing count 1

第1题：

第2题：

While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）

• A、Serial 0 is up, line protocol is up
• B、Serial 0 is up, line protocol is down
• C、Serial 0 is down, line protocol is down
• D、Serial 0 is down, line protocol is up
• E、Serial 0 is administratively down, line protocol is down
• F、Serial 0 is administratively down, line protocol is up

第3题：

第4题：

YOU issue the pins interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）

• A、The bypass-routing parameter is used to test the density on the TI line.
• B、The bypass-routing parameter cannot be used on a T1 interface.
• C、The bypass-routing parameter allows you to ping a host through an interface that has no route through it.
• D、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic

第5题：

You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）

• A、The count parameter creates a counter that you can view with the show firewall command.
• B、The count parameter allows the router to count the number of pings for logging purposes.
• C、The count parameter allows the router to pause for 1000 seconds before sending out a ping.
• D、The count parameter allows the router to send out 1000 pings and then stop.

第6题：

Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet（）。

• A、The IP address of sever 1.
• B、The MAC address of NIC in sever 1.
• C、The IP address of F0/0 interface of router R1.
• D、The MAC address of the Fa0/0 interface of router R1.
• E、The IP address of the s0/0/0 interface of router R2
• F、The MAC address of the s0/0/0 interface of router R2

第7题：

You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）

• A、The count parameter creates a counter that you can view with the show firewall command
• B、The count parameter allows the router to count the number of pings for logging purposes
• C、The count parameter allows the router to pause for 10000 seconds before sending out a ping
• D、The count parameter allows the router to send out 1000 pings and then stop

第8题：

第9题：

You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）

• A、The bypass-routing parameter is used to test the density on the T1 line.
• B、The bypass-routing parameter cannot be used on a T1 interface.
• C、The bypass-routing parameter allows you to ping a host through an interface that has no route through it.
• D、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.

第10题：

When applying the configuration in the exhibit and initializing a chassis cluster， which statement is correct？（） [edit chassis] user@host# show cluster { reth-count 3； redundancy-group 1 { node 0 priority 1； node 1 priority 100； } }

• A、Three physical interfaces are redundant.
• B、You must define an additional redundancy group.
• C、node 0 will immediately become primary for redundancy group 1.
• D、You must issue an operational command and reboot the system for the above configuration to take effect.