You are the network administrator for Ezonexam. You are installing Windows 2000 Server on a new computer by using the Windows 2000 Server compact disk. The computer has five 18-GB hard disks Dick0, Disk1, Disk2, Disk3, and Disk4. The disks do not have any partitions defined.
You want to use as much space on Disk0 as possible for the partition on which Windows 2000 Server is installed. You want the disk on which you install Windows 2000 Server to be fault tolerant. You also want as much disk space as possible across the other disks to be available for data storage and to be fault tolerant.
What should you do? (Each correct answer presents part of the solution. Choose three)
A. Install Windows 2000 Server on a 4-GB NTFS partition on Disk 0. Configure the five disks as dynamic disks.
B. Install Windows 2000 Server on a 18-GB NTFS partition on Disk 0. Configure the five disks as dynamic disks.
C. Create a RAID-5 volume using Disk2, Disk3, and Disk4.
D. Create a stripped volume using Disk2, Disk3, and Disk4.
E. Create a RAID-5 volume using all disks.
F. Create a stripped volume using all disks.
G. Select the volume on Disk0 and add a mirror using Disk1.
第1题:
You are the desktop administrator for Ezonexam.com'ssalesdepartment. Ezonexam.com's network contains a RIS server.
You need to install Windows 2000 Professional on a computer that has a SCSI disk subsystem. You start the computer by using the Windows 2000 Professional CD-ROM, and you begin the installation.
However, Setup reports that it cannot find any disk on which to install Windows 2000 Professional.
You start the computer by using a RIS bootable floppy disk, and you receive the same result.
What should you do?
A.Add an answer file to the root directory of the RIS bootable floppy disk. Start the computer by using the RIS bootable floppy disk, and run Setup by using RIS.
B.Add the SCSI-controller driver to the root directory of the RIS bootable floppy disk. Start the computer by using the RIS bootable floppy disk, and run Setup by using RIS.
C.Start the computer by using the Windows 2000 Professional CD-ROM, and run Setup. After Setup starts, provide an answer file on a floppy disk.
D.Start the computer by using the Windows 2000 Professional CD-ROM, and run Setup. After Setup starts, provide a SCSI-controller driver on a floppy disk.
E.Start the computer by using the Windows 2000 Professional CD-ROM, and run Setup. After Setup starts, provide the appropriate HAL on a floppy disk.
第2题:
You are the network administrator for Ezonexam. You are preparing to install Windows 2000 Server on a new computer. The computer is connected to a network that includes Windows 98 computers and Windows 2000 Server computers.
You want to install Windows 2000 Server from source files that are located on a shared folder called I386 on a Windows 2000 Server computer named Ezonexam1.
What should you do? (Each correct answer presents part of the solution. Choose two)
A.On a Windows 2000 computer, use Makebt32.exe to create installation startup disks. Start the new computer by using the first disk.
B.On a Windows 2000 computer, format a floppy disk. Copy NTLDR, Boot.ini, Ntdetect.com, and Ntbootdd.sys to this disk. Start the new computer by using the disk.
C.Start the new computer by using a Windows 98 network boot disk.
D.Connect to \\Ezonexam1\I386 and run Winnt32.exe.
E.Connect to \\Ezonexam1\I386 and run Winnt.exe.
第3题:
You need to install Windows 2000 Server on one of your older Windows NT Server 4.0 computers. The server has dual processors, 2 GB of RAM, a RAID controller with five SCSI hard disks in an array, and a generic 10/100-MB network adapter. You begin the server installation by updating the SCSI firmware.
You then start the installation of the Windows 2000 Server operating system. During the next portion of the installation, you receive an error message indicating that no hard disks can be found.
You want to successfully install Windows 2000 Server on the computer.
What should you do? (Each correct answer presents part of the solution. Choose two)
A.Restart the installation by using the Windows 2000 Installation CD-ROM. Press F3 during the text-mode setup.
B.Restart the installation by using the Windows 2000 Installation CD-ROM. Press F6 during the text-mode setup.
C.Restart the installation by using a MS-DOS boot disk with a CD-ROM driver.
D.Insert a disk with the original SCSI firmware.
E.Insert a disk with the OEM SCSI driver.
第4题:
You are the administrator of a Windows 2000 Server network. On each server, you format a separate system partition and a separate boot partition as NTFS.
Several months later, you shut down one of the servers for the maintenance. When you try to restart the server, you receive the following error message "NTLDR is missing. Press any key to restart".
You want to install a new NTLDR file on the server, but you do not want to lose any settings you made since the original installation. What should you do?
A.Start the computer by using the Windows 2000 Server CD-ROM and choose to repair the installation. Select the Recovery Console and copy the NTLDR file on the CD-ROM to the root of the system volume.
B.Start the computer by using the Windows 2000 Server CD-ROM and choose to reinstall. When installation is complete, copy the NTLDR file to the root of the boot volume.
C.Start the computer by using a Windows 2000 bootable floppy disk. From the command prompt, run the sfc/scanboot command.
D.Start the computer by using a Windows 2000 bootable floppy disk. Run the File Signature Verification utility.
第5题:
You are the administrator for your company's network. The network is configured as shown in the exhibit.
You want to install Windows 2000 Professional on 20 new PXE-compliant computers on the marketing segment of your network. The new computers do not have operating systems installed.
You create a RIS image. You load the image onto the RIS server. You then start the new computers.
You find that the new computers cannot connect to the RIS server. You verify that the new computers cannot connect to the RIS server. You verify that the existing client computers in the network can connect to the network servers, including the RIS server. You want to enable the new computers to connect to the RIS server.
What should you do?
A.Add a Windows 2000 Server computer running WINS to the network.
B.Add a Windows 2000 Server computer running DHCP to the network.
C.Add the domain Everyone group to the RIS OS image security settings.
D.Place the new computers on the same segment as the RIS server.
第6题:
You are the administrator of your company's network. The network is configured as shown in the exhibit.
You want to install Windows 2000 Professional on 10 non-PXE-compliant computers that are on the marketing segment of your network. You start one of the computers by using a RIS boot disk. However, you cannot connect to the RIS server.
You verify that the existing client computers on the network can connect to network servers, including the RIS server. The network router does not support BOOTP, so existing client computers use manually configured TCP/IP addresses. You want to enable the computers to connect to the RIS server.
What should you do?
A.Add a computer running DHCP Relay Agent to the marketing segment.
B.Add a computer running the network monitor driver to the marketing segment.
C.Move the Windows 2000 Server computer running WINS to the marketing segment.
D.Move the Windows 2000 Server computer running Active Directory to the marketing segment.
第7题:
You are the administrator of a network that consists of a single Windows NT 4.0 domain. The network contains five Windows NT Server domain controllers and 1,000 Windows NT Workstation client computers.
You want to install Windows 2000 Server on a new computer. You want the new computer to act as domain controller in the existing domain.
What should you do?
A.On the new computer, install Windows NT Server 4.0 and designate the computer as a BDC in the existing domain. Promote the computer to the PDC of the domain. Upgrade the computer to Windows 2000 Server.
B.On the new computer, install Windows NT Server 4.0 and designate the computer as a PDC in a new domain that has the same NetBIOS name as the existing Windows NT domain. Upgrade the computer to Windows 2000 Server. Use the Active Directory sites and services to force synchronization of the domain controllers.
C.Shut down the PDC of the existing Windows NT domain from the network. On the new computer, install Windows 2000 Server, and then run the Active Directory installation wizard to install Active Directory, specifying the same NetBIOS name for the Windows 2000 domain as the existing Windows NT domain. Restart the Windows NT PDC on the network and demote it to a BDC.
D.Shut down the PDC of the existing Windows NT domain from the network. On the new computer, install Windows 2000 Server, and then run the Active Directory installation wizard to install Active Directory as a replica in the existing Windows NT domain. Promote the new computer to the PDC of the domain. Restart Windows NT PDC on the network and demote it to a BDC.
第8题:
You are the network administrator for Ezonexam. The network includes a Microsoft Windows NT Server 4.0 member server computer that has a non-Plug and Play ISA network adapter.
You want to upgrade this computer to Microsoft Windows 2000 Server. You also want to ensure that you maintain the current device configuration during the upgrade.
What should you do? (Each correct answer presents part of the solution. Choose two)
A. Install the latest driver for the network adapter.
B. Disable the network adapter.
C. Start the upgrade process by using Winnt32.exe
D. Start the upgrade process by booting from the Windows 2000 Server compact disc.
E. Configure BIOS to reserve the IRQ currently in use by the network adapter.
F. Press F6 at the beginning of the text mode setup to specify an additional driver.
第9题:
Your Windows 2000 Server computer named EzonexamSrv contains a single 18-GB hard disk. The drive is configured as a basic disk and has two partitions. Partition C is 2 GB in size and contains the operating system files. Partition D is 16 GB in size and contains user data that is updated frequently.
Both partitions are formatted as NTFS. Both partitions are backed up to a tape every evening at 10:00 P.M.You have a current Emergency Repair Disk (ERD) for EzonexamSrv, and the Recovery Console is installed on the computer.
One day at4:00 P.M., the server fails. You attempt to restart EzonexamSrv, but you receive the following error message:
"Boot disk or operating system not found".
You use Recovery Console to discover that the files on partition C are corrupted.
You need to recover EzonexamSrv from the failure as quickly as possible. You also must recover as much user data as possible.
What should you do?
A.Use the ERD to start the computer. Replace the corrupted files on partition C by copying them from a Windows 2000 Server CD-ROM.
B.Boot the Recovery Console. Copy any files that have changed since 10:00 P.M. the previous evening to a second server. Use the most recent tape backup to restore the remaining user data to the second server.
C.Start the computer by using a Windows 2000 Server CD-ROM. Select the Repair option in Setup.
D.Install a second hard disk in the computer. Install Windows 2000 Server on the new hard disk. Re-create the shared folders on the first hard disk.
第10题:
Ezonexam has 50 offices. The employees in these offices have limited knowledge of Windows 2000. Each office has a network of between five and 20 client computers. The office networks are connected to each other. The company is buying 50 identical computers to run Windows 2000 Server in these offices. The server must be installed to the company's standard configuration. You use Setup Manager to create a network shared distribution folder and a Unattend.txt file that specifies the company's standard configuration.
You want to automate the installation process as much as possible, in the least possible amount of time.
What should you do?
A.Run Makebt32.exe to create four installation startup disks and add the Unattend.txt file to the first disk. Instruct an employee at each office to start the installation by using these disks.
B.Create a Microsoft MS-DOS network boot disk that makes a connection to the network shared distribution folder and runs the winnt command with the /s and /u switches. Instruct an employee at each office to start the installation by using this disk.
C.Create a floppy disk that contains only the Unattend.txt file. Instruct an employee at each office to start the installation by using the Windows 2000 Server compact disc, with the floppy disk inserted.
D.Create a Windows 2000 folder on a hard disk. Copy the Windows 2000 Server compact disc to the folder. Add the Unattend.txt file to the folder. Copy the folder to a writeable CD. Instruct an employee at each office to start the installation by suing this CD.