/etc/nodename
/etc/hostname.rtls0
/etc/hostname
/etc/inet/hosts
/etc/domainname
/etc/inet/ipnodes
/etc/inetd.conf
第1题：
A. It is a route to be used when the routing protocol fails.
B. It is a route configured by an ISP that sends traffic into a corporate network.
C. It is a route used when a packet is destined for a remote network that is not listed in the routing table.
D. It is a route manually configured for a specific remote network for which a routing protocol is not configured.
E. It is used to send traffic to a stub network.
第2题：
You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）
A. The Frame Relay encapsulation on the physical interface.
B. The local DLCI on each subinterface.
C. An IP address on the physical interface.
D. The subinterface type as point-to-point.
第3题：
You have a firewall filter applied in an inbound direction on a customer interface. You would like this filter to protect your network from a spoofed denial of service attack. Which action should be configured to accomplish your goal?（）
A. then reject
B. then discard
C. then next filter
D. then silent-drop
第4题：
You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）
第5题：
You have just created a new VLAN on your network for inter-VLAN routing. What is one step that you should include in your VLAN-based implementation and verification plan？（）
第6题：
You work as a network engineer at TestKing.com. TestKing users have noticed extremely slow network performance, intermittent connectivity, and connection loss. After entering the show interfaces command, you notice that the Ethernet interface is configured as 100 Mbps full-duplex and that there is evidence of late collisions. What could be the cause of this problem?（）
A. duplex mismatch
B. a routing loop
C. trunking mode mismatch
D. improperly configured root bridge
E. improperly configured static VLAN
第7题：
A.an OSPF update for network 192.168.0.0/16
B.a static router to network 192.168.10.0/24
C.a static router to network 192.168.10.0/24 with a local serial interface configured as the next hop
D.a RIP update for network 192.168.10.0/24
E.a directly connected interface with an address of 192.168.10.254/24
F.a default route with a next hop address of 192.168.10.1
第8题：
A. Any routes learned by R2 from the interface tied to the 172.16.0.0 network will not be advertised to neighbors on the 192.168.2.0 network.
B. Only routes learned by R2 from the interface tied to the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
C. Only the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
D. All networks, except the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network .
第9题：
You work as a network engineer at TestKing.com. TestKing users have noticed extremely slow network performance, intermittent connectivity, and connection loss. After entering the show interfaces command, you notice that the Ethernet interface is configured as 100 Mbps full-duplex and that there is evidence of late collisions. What could be the cause of this problem?（）
第10题：
You are using AutoQoS Enterprise and realize that the results are not what you expected. Whichof the following are possible reasons for AutoQoS not functioning correctly？（Choose all thatapply.）（）