Check the WX device remote interface and verify that the status is up.
From the WX device, ping the default gateway to make sure it is reachable.
In WebView, check the service tunnel status under Compression > Basic > Endpoints.
In WebView, check the remote routes under Compression > Advanced > Remote Routes.
第1题:
A. Remote routes are the compression subnets advertised by remote WX devices.
B. Remote routes include routes for remote hosts or subnets advertised by a WAN router.
C. Remote routes are the routes advertised by remote routers that are more than two hops away.
D. Remote routes are the compression subnets advertised by the local WX device to the remote WX devices.
第2题:
A. Check the WX device remote interface and verify that the status is up.
B. From the WX device, ping the default gateway to make sure it is reachable.
C. In WebView, check the service tunnel status under Compression > Basic > Endpoints.
D. In WebView, check the remote routes under Compression > Advanced > Remote Routes.
第3题:
CDP is being used throughout the Ezonexam network. What are two reasons why the Ezonexam network administrator would use CDP? (Choose two)
A. To determine the status of network services on a remote device
B. To obtain the IP Address of a connected device in order to telnet to the device
C. To verify the type of cable interconnecting two devices
D. To verify Layer 2 connectivity between two devices when Layer 3 fails
E. To obtain VLAN information from directly connected swticehs
F. To determine the status of the routing protocols between directly connected routers
G. To support automatic network failover during outages
第4题:
A. The PC has connectivity with a local host.
B. The PC has connectivity with a Layer 3 device.
C. The PC has a default gateway correctly configured
D. The PC has connectivity up to Layer 5 of the OSI model
E. The PC has the TCP/IP protocol stack correctly installed.
第5题:
A. Define the virtual router IP address on both WXC devices.
B. Add a static route for the virtual router IP address on both WXC devices.
C. Define the physical IP address of each router on each respective WXC device.
D. Leave the default gateway field in the WXC device blank; it will automatically detect the active gateway address.
第6题:
A. Admin > Device
B. Device Setup > Topology
C. Compression > Endpoints
D. Device Setup > Advanced > Topology
第7题:
A. SSH
B. Telnet
C. WebView
D. device front panel
E. serial console (command-line interface)
第8题:
You configure an HP Jet Direct print device as sown in the Network Diagram exhibit.
You want to create and share a printer at Srv2.sales.justtogs.com that is connected to the TCP/IP port of the print device. However, when you enter the IP address of the device, you receive the dialog box shown in thePrinterPortWizard exhibit.
PrinterPortWizard
What should you do?
A.Select Hewlett Packard JetDirect from the Standard drop-down list.
B.Select the Custom option button, click the Settings command button, and select the LPR protocol.
C.Change the IP address of the print device to 10.5.20.200.
D.Change the subnet mask of the print device to 255.0.0.0.
E.Change the default gateway address on Srv2.sales.justtogs.com to 10.5.20.100.
第9题:
A. Make sure that the network server can be accessed.
B. Check that the authentication for access is set.
C. Assure that the network server has adequate space for the code image.
D. Verify any file naming and path requirements.
E. Make sure that the server can load and run the bootstrap code.
第10题:
A. to verify the type of cable interconnecting two devices
B. to determine the status of network services on a remote device
C. to obtain VLAN information from directly connected switches
D. to verify Layer 2 connectivity between two devices when Layer 3 fails
E. to obtain the IP address of a connected device in order to telnet to the device
F. to determine the status of the routing protocols between directly connected routers