DLPAR functions are not available for cloned partitions
The new partition has the same node number as the original LPAR
Additional filesets need to be reinstalled after the alt_disk_install cloning
The speed and duplex settings on the Ethernet adapter on the new LPAR is misconfigured
第1题:
You are trying to bring up a new Testking location onto your existing frame relay network. The new location is using an Adtran router and you are having difficulties getting the site to connect via frame to your Cisco HQ router. What is the most likely cause of the problem?()
A. Mismatched LMI types.
B. Incompatible encapsulation types.
C. Mismatching IP addresses.
D. Incorrect DLCI.
E. None of the above
第2题:
A system administrator is creating four LPARs on a Power 550. The Power 550 has 64GB of memoryinstalled and 32GB activated. The system administrator sets the minimum dedicated memory to 8GB in the profile for each LPAR. After activating three LPARs, he is not able to activate the fourth LPAR. What is the likely cause of the problem?()
第3题:
After connecting a PC to an available port on a switch, you find that the PC can not access any of the resources on the LAN. No other PC's connected to the switch appear to be having any issues. What is the most likely cause for this problem?
A.The router lacks a routing table entry for the new host
B.The host switch port is assigned to the incorrect VLAN
C.The host MAC address is incorrectly configured
D.A STP instance for the new host has not been initialized
E.The switch does not have the MAC address hard coded in the CAM table.
第4题:
A customer has shut down an LPAR after using DLPAR to add or remove processor and memory resources. When the partition is reactivated, the desired changes are missing. What action, or sequence of actions, will immediately and permanently solve this problem?()
第5题:
Companycom is migrating from a p690 to a p5 595 utilizing APV Virtual IO features. They have created their profiles for their two Virtual IO Servers. The first Virtual IO Server is installed and running. When trying to DLPAR the DVD/ROM the task fails on the HMC. What is the probable cause?()
第6题:
A client is experiencing issues after cloning an LPAR using alt_disk_install. DLPAR functions are not available for the new LPAR. Also, there is a lot of network traffic to the HMC. What is the most probable cause of this problem?()
第7题:
Companycom has just purchased a p5 570 with AIX 5.3. The customer would like to add a training LPAR to the system, but no processors are available. All of the partitions are using dedicated resources. The test LPAR is using one processor and has a 90% CPU idle rate. What can be done to setup this training LPAR quickly without disabling their current environment?()
第8题:
The system administrator did a new install of AIX on a server about a week ago. The system was not rebooted after the installation. CDE is running on this system as is TCPIP. The system administrator has started configuring the system percompany directives. The power cable was inadvertently disconnected from the wall causing the sever to lose power. Upon reboot, the system appears to hang during log in from the console or from Xterminals. Which of the following is the most probable cause?()
A.It is a hardware problem caused by the power failure.
B.There is a network problem, most probably with name resolution.
C.Sine the system was never rebooted, devices are marked defined instead of available and need to be activated.
D.Some filesets may be marked as broken and need to be reinstalled.
第9题:
Companycom is installing a p5 595 with AIX 5.3. The DLPAR option for the resources cannot be selected on the HMC menus. However, the daemons are running on both the HMC and LPARs. Which of the following is a prerequisite for DLPAR functionality?()
第10题:
An adapter state does not show available after a reboot. Which of the following is the most probable cause?()