Router R1 has been configured for EIGRP. The configuratio n

Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP.Which one of the following is true?（）

A. R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.

B. For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.

C. For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.

D. No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.

A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.

B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.

C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.

D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.

E. The Hello parameters on routers R1 and R2 do not m atch.

How can a Ezonexam administrator determine if a router has been configured when it is first powered up?

A．A configured router prompts for a password

B．A configured router goes to the privileged mode prompt

C．An un configured router goes into the setup dialog

D．An un configured router goes to the enable mode prompt

A. The no auto - summary command has not been issued under the EIGRP process on both routers.

B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.

C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.

D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.

Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）

A. Add the area 1 stub command on routers R1.

B. Add the always keyword to the default - information originate configuration command on router R2.

C. Remov e the default information originate configuration command from router R2 and place it on router R1.

D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

A. The route to 10.2.0.0/16 was redistributed into EIGRP.

B. A default route has been redistributed into the EIGRP autonomous system.

C. R1 is configured with the ip summary - address command.

D. R1 is sourcing a n external EIGRP route from Null0.

E. The router at 10.1.1.2 is configured with the ip default - network 0.0.0.0 command.

F. R1 is configured with the variance command.

Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP.Which of the following answers lists an item that cannot be matched by route map fred?（）

A. Subnet number

B. Next - hop router IP address of the route

C. Whether the route is an E1 or E2 route

D. The ro ute‘s tag

E. The number of router hops between the router and the subnet

A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）

A. one

B. three

C. two

D. zero