All of the routers need to be configured for backbone Area 1.
R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
The hello and dead interval timers are not set to the same values on R1 and R3.
EIGRP is also configured on these routers with a lower administrative distance.
R1 and R3 are configured in different areas.
第1题：
Routers R1 and R2, OSPF neighbors in area 0 over their Fa0/0 interfaces (respectively), currently both successfully use OSPF MD5 authentication. The OSPF configuration includes the area 0 authentication command under the router ospf 1 command.Which of the following commands must have been configur ed on R1‘s Fa0/0 interface?（）
A. ip ospf authentication null
B. ip ospf authentication message - digest
C. ip ospf authentication -key whatever- it - is
D. ip ospf message - digest - key 1 md5 whatever - it - is
E. ip ospf md5 1 key whatever - it - is
第2题：
A.show ip ospf
B.show ip ospf interface
C.show ip ospf neighbor
D.show ip ospf database
E.show ip ospf statistics
F.show running - config begin router ospf
第3题：
A.initial
B.exchange
C.full
D.establish
第4题：
A. RTA will not establish an OSPF adjacency w ith RTB
B. RTA will send OSPF hello packets, but will not send OSPF updates
C. RTA will not accept OSPF hello packets from RTB
D. RTA will send OSPF updates, but will not establish an adjacency with RTB
第5题：
A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.
B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.
C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.
D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.
E. The Hello parameters on routers R1 and R2 do not m atch.
第6题：
Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribu tion is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1?（）
A. the routes originating from the RIP routing domain
B. the routes originating from the OSPF stub area
C. all OSPF inter and intra - area routes
D. all routes originating from RIP and OSPF routing domains
第7题：
A. stub
B. totally stubby
C. NSSA
D. totally NSSA
第8题：
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP.Which one of the following is true?（）
A. R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.
B. For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.
C. For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.
D. No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
第9题：
Refer to the exhibit. Routers R1 and R2 have been configured to operate with OSPF. Routers R1 and R3 have been configured to operate with RIP. After configuring the redistribution between OSPF a nd RIP on R1, no OSPF routes are distributed into RIP. What should be done to correct this problem? （）
A. The redistribution command should be reentered with the match route - type parameter included.
B. The redistribution command should be reentered wit h the route - map map - tag parameter included.
C. The redistribution command should be reentered with the metric metric - value parameter included.
D. Routes will first need to be distributed into another protocol, and then into RIP.
第10题：
A. show i p ospf
B. show ip ospf interface
C. show ipv6 ospf interface
D. show ipv6 ospf