the IP address of the first Fast Ethernet interface
the IP address of the console management interface
the highest IP address among its active interfaces
the lowest IP address among its active interfaces
the priority value until a loopback interface is configured
第1题:
A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.
B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.
C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.
D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.
E. The Hello parameters on routers R1 and R2 do not m atch.
第2题:
A. Only redistributed RIP routes will appear in Area 1. They will be advertised via t ype 7 LSAs
B. No redistributed routes can appear in Area 1, only summary routes
C. Redistributed RIP and IGRP routes will appear in Area 1. They will be advertised via type 5 LSAs
D. Only redistributed IGRP routes will appear in Area 1. They will be advertised via type 7 LSAs
第3题:
A. all routers on a link
B. all routers in an area
C. all external OSPF peers
D. all routers in an OSPF domain
第4题:
A.network 0.0.0.0 255.255.255.255 area 0
B.network 0.0.0.0 0.0.0.0 area 0
C.network 255.255.255.255 0.0.0.0 area 0
D.network all-interfaces area 0
第5题:
A. On the ABR router ospf 10 area 3 stub
B. On all Area 3 routers router ospf 10 area 3 stub
C. On all Area 3 routers router ospf 10 area 3 stub no - summary
D. On the ABR router ospf 10 area 3 nssa
E. On the ABR rou ter ospf 10 area 3 stub no - summary
第6题:
A. Hierarchical OSPF networks need to be in one area
B. Multiple OSPF areas must connect to area 0
C. Single area OSPF networks must be configured in area 1
D. Areas can be assigned any number from 0 to 63535
E. Area 0 is called the backbone area
F. Each OSPF area need to be configured with a loopback interface
第7题:
OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? ()
A. The ip ospf network broadcast command should be configured on each Frame Relay interface
B. The ip ospf network non -broadcast command should be configured on each Frame Relay interface
C. Th e ip ospf priority value on the spoke routers should be set to 0
D. The ip ospf priority value on the hub router should be set to 0
E. The neighbor command should be configured under the OSPF routing process on all routers
第8题:
Refer to the exhibit. OSPF is configured on all routers in the network. Area 5 is configured as an NSSA areA. The RIPv2 routes are redistributed into the OSPF domain on router R5. What two types of LSAs will be originated by router R5?()
A. type 1 Router LSA
B. type 2 Network LSA
C. type 3 Network Summary LSA
D. type 4 ASBR Summary LSA
E. type 5 AS External LSA
F. type 7 NSSA External LSA
第9题:
A. the IP address of the first Fast Ethernet interface
B. the IP address of the console management interface
C. the highest IP address among its active interfaces
D. the lowest IP address among its active interfaces
E. the priority value until a loopback interface is configured
第10题:
A. Each OSPF area requires a loopback interface to be configured.
B. Areas may be assigned any number from 0 to 65535.
C. Area 0 is called the backbone area.
D. Hierarchical OSPF networks do not require multiple areas.
E. Multiple OSPF areas must connect to area 0.
F. Single area OSPF networks must be configured in area 1.