问题:Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? ()A、Configure a non-unique address on the loopback interface for use by the PIM RP.B、Configure MSDP with the unique address (router ID) as the local address of the peer.C、Configure MSDP with the non-unique address (router ID) as the local address of the peer.D、Configure a unique address on the loopback interface, used as the PIM RP.
查看答案
问题:Which two multicast groups support Auto-RP mapping and discovery?()A、224.0.0.39B、224.0.1.39C、224.0.0.40D、224.0.1.40
问题:In which three ways are C-BGP and E-BGP sessions similar?()A、Both are configured as type external.B、Both configurations use the peer-as command.C、Neither advertises the local-preference attribute.D、Both set next-hop self when advertising routes to peers.E、Both modify the AS-path attribute when advertising routes.
问题:Which statement is true regarding an Ethernet collision domain?()A、If a router is used, the collision domain includes all devices connected to the router.B、If a hub is used, the collision domain is limited to each device and the hub.C、If a switch is used, the collision domain is limited to each device and the switch.D、If a bridge is used, the collision domain includes all devices connected to the bridge.
问题:Which statement is correct about policies in the Junos OS?()A、Export policies are used to filter routes from the RE forwarding table to the PFE forwarding table.B、Export policies are used to filter routes destined for the routing table.C、Export policies are used to filter routes being sent to neighboring devices.D、Export policies are used to filter traffic leaving the device.
问题: Given the following MPLS L2 configuration command: mpls-relay 10.1.1.1 4 Which two statements true? ()(Choose two.)A、This command is applied to the core router facing interface.B、This command is applied to the customer facing interface.C、The 4 is locally significant and identifies the layer 2 circuit.D、The 4 must match exactly on the peer router configuration on the remote end.
问题:What is the last CoS process performed prior to a packet leaving a router?()A、Rewrite MarkerB、Multifield ClassifierC、PolicingD、BA Classifier
问题:Which statement is true about "sticky" load balancing for Clusters? ()A、The "clientip" setting does not apply to clusters, it only pertains to a Forwarder.B、When set to "clientip" it uses the client's IP address to bind the client to a particular target server.C、When set to "clientip" it allows a DX sticky cookie to be sent to and stored by the client based on the IP address.D、When set to "clientip" it ensures that all subsequent requests are directed to the same client that made the initial request.
问题:What is one way to escape hardware bypass mode?()A、Reset the cabling.B、Power cycle the device.C、Bounce the service tunnels.D、Unlock the device from the console.
问题:Which statement is true regarding an Ethernet collision domain?()A、If a router is used, the collision domain includes all devices connected to the routerB、If a hub is used, the colision domain is limited to each device and the hubC、If a switch is used, the collision domain is limited to each device and the switchD、If a bridge is used, the collision domain includes all devices connected to the bridge
问题:Which CLI command displays all OSPF LSAs received by the local router?()A、show ospf neighborB、show ospf databaseC、show ospf interfaceD、show ospf adjacency
问题:What is the purpose of the OSPF link-state update packet?()A、describes a change to the OSPF hello timerB、carries one or more link-state advertisementsC、establishes and maintains neighbor relationshipsD、describes the contents of the entire link-state database
问题:Which two are uses of NAT?()A、enabling network migrationsB、conserving public IP addressesC、allowing stateful packet inspectionD、preventing unauthorized connections from outside the network
问题:What is the proper command to create a DHCP address pool?()A、ip local-poolB、ip local poolC、ip dhcp local poolD、ip dhcp-local pool
问题:In a Junos Pulse Access Control Service firewall enforcement configuration, what is the purpose of the source IP policy?()A、to specify the destination addresses to which access is permittedB、to specify the source address permitted to access the resourceC、to specify the services to which access is permittedD、to inform the enforcer to expect policy information from the Junos Pulse Access Control Service
问题:What is one function of MBGP?()A、extending IPSec tunnelsB、carrying multiple address familiesC、propagating DVMRP routing informationD、extending Autonomous System GRE tunnels
问题:What is true when designing OSPF import routing policy in JUNOS software?()A、Import policies are not possible.B、Import policies only match on external routes.C、Import policies only match on internal routes.D、Import policies can cause inconsistent link state databases.
问题:An enterprise has a web application running both HTTP and HTTPS. How many Clusters must becreated?()A、1B、2C、3D、4
问题:Which two are default preference values for both internal and external IS-IS Level 2 routes on a Juniper Networks router?()A、10B、15C、18D、150E、160F、165
问题:In a PPP over ATM environment,which two PPP authentication methods are supported by the ERX Edge Router?()A、IKEB、PAPC、CHAPD、MSCHAP