违法和不良信息举报 联系客服
免费注册 登录

For a router to successfully red

题目

For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）

  • A、The router must have one routing protocol configured, but configuration for both routing protocols is not necessary
  • B、The router must hav e at least one working link connected to each routing domain
  • C、The redistribute command must be configured under EIGRP to send the routes to OSPF
  • D、The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
如果没有搜索结果或未解决您的问题，请直接 联系老师 获取答案。
相似问题和答案

第1题：

On which component are RED and WRED managed in the router?()

A. I/O module

B. switch fabric

C. egress line module

D. ingress line module


参考答案：C

第2题：

WhichofthefollowingisthecorrectwiringorderforanRJ－11twolinejack?()

A.Black，Green，Red，Yellow

B.Black，Red，Green，Yellow

C.Red，Black，Green，Yellow

D.Yellow，Red，Green，Black


参考答案：B

第3题：

After working all night and successfully configuring a Cisco router for the Ezonexam network you save your changes on the startup config, reboot the router, and go out for a cigarette. When you return, none of your changes are active and the router boots to the initial configuration mode! Which of the choices below indicates the source of your problem?

A．Hardware failure in NVRAM prevents the router from loading the config

B．Startup-config in flash is corrupt and cannot be analyzed

C．Router configuration-register set to bypass startup configuration

D．Startup-config in NVRAM is corrupt and cannot be analyzed

E．None of the above


正确答案：C
解析：Explanation:
The default configuration-register setting of 0x2102 loads the IOS from flash and the configuration from NVRAM.
However, for password recovery, you can set the register to 0x2142 and the startup-config file in NVRAM will be bypassed. The problem described here is that the config register was not changed back to 0x2102 before the router was rebooted, so the active configuration is bypassed. Simply setting the config register back to 0x2102 will fix this problem.

Incorrect Answers:
A, B, D. All of these describe hardware or software errors. In the event that this is the problem, errors will be generated and the router will fail to boot properly. In these cases, the router will not return to the initial startup configuration.

第4题：

Mark the joining shackles with （）paint.

  • A、red/yellow
  • B、yellow/black
  • C、red/white
  • D、yellow/red

正确答案:C

第5题：

Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）

A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0

B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0

C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0

D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0

E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0

F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0


参考答案：B

第6题：

Which two commands will successfully create ping traffic?()

A. user@router# ping 10.10.10.1

B. user@router# run ping 10.10.10.1

C. user@router> ping 10.10.10.1

D. user@router> request ping 10.10.10.1


参考答案：B, C

第7题：

Red Hat Enterprise Linux版本分为( )。

A.Red Hat Enterprise Linux AS

B.Red Hat Enterprise Linux ES

C.Red Hat Enterprise Linux BS

D.Red Hat Enterprise Linux WS


参考答案：ABD

第8题：

Linda wore a () skirt yesterday.

A、red beautiful silk

B、beautiful red silk

C、beautiful silk red


正确答案:B

第9题：

What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? ()

A.0x2100

B.0x2101

C.0x2102

D.0x2124

E.0x2142


参考答案：C

第10题：

Which command can be used on a PE router to connect to a CE router （11.1.1.4） in VRF red？（）

  • A、telnet 11.1.1.4 /vrf-source red
  • B、telnet 11.1.1.4 source /vrf red
  • C、telnet 11.1.1.4 /source vrf red
  • D、telnet 11.1.1.4 /vrf red
  • E、telnet 11.1.1.4 vrf red

正确答案:D

更多相关问题
相关内容