违法和不良信息举报 联系客服
免费注册 登录

Which commands are required to properly configure a router t

题目
多选题
Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）
A

Router（config）#router ospf 1

B

Router（config）#router ospf 0

C

Router（config）#router ospf  area 0

D

Router（config-router）#network 192.168.16.0 0.0.0.255 area 0

E

Router（config-router）#network 192.168.16.0 0.0.0.255 0

F

Router（config-router）#network 192.168.16.0 255.255.255.0 area 0

如果没有搜索结果或未解决您的问题，请直接 联系老师 获取答案。
相似问题和答案

第1题：

An engineer is reviewing another engineer‘s sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）

A. tunnel source

B. tunnel destination

C. tunnel mode

D. All these commands are requireD


参考答案：C

第2题：

A network administrator needs to configure a router for a Frame Relay connection to a non－Cisco router. Which of the following commands will prepare the WAN interface for this connection?()

A. Router(config-if)# encapsulation frame-relay q933a

B. Router(config-if)# encapsulation frame-relay ansi

C. Router(config-if)# encapsulation frame-relay ietf

D. Router(config-if)# encapsulation frame-relay isl

E. None of the above


参考答案：C

第3题：

You would like to configure a fractional T1 interface on a channelized T3 controller with the following properties:Which set of configuration commands accomplishes this goal?()

A.A

B.B

C.C

D.D


参考答案：D

第4题：

A network administrator needs to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface for this connection?（）

  • A、Router(config-if)# encapsulation frame-relay q933a
  • B、Router(config-if)# encapsulation frame-relay ansi
  • C、Router(config-if)# encapsulation frame-relay ietf
  • D、Router(config-if)# encapsulation frame-relay isl
  • E、None of the above

正确答案:C

第5题：

Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0／24 to OSPF area 0?()

A.Router(config)#router ospf 1

B.Router(config)#router ospf 0

C.Router(config)#router ospf area 0

D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0

E.Router(config-router)#network 192.168.16.0 0.0.0.255 0

F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0


参考答案：A, D

第6题：

Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?()

A. On the ABR router ospf 10 area 3 stub

B. On all Area 3 routers router ospf 10 area 3 stub

C. On all Area 3 routers router ospf 10 area 3 stub no - summary

D. On the ABR router ospf 10 area 3 nssa

E. On the ABR rou ter ospf 10 area 3 stub no - summary


参考答案：E

第7题：

Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?()

A. Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0

B. Router(config)# ip route 0.0.0.0 255.255.255.255 s0

C. Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0

D. Router(config)# ip route 0.0.0.0 0.0.0.0 s0

E. Router(config)# ip route any any e0


参考答案：D

第8题：

Which two configuration commands are required to direct debug level console logging to your current ERX Edge Router Telnet session?()

A.A

B.B

C.C

D.D


参考答案：A, C

第9题：

What are the basic configuration steps to enable IS - IS?（）

  • A、Configure the net system - id command under routerisis and enable IS - IS on each interface with the ip router isis command.
  • B、Configure the net sy stem - id and the network net - id commands under routerisis.
  • C、Configure the network net - id command(s) under routerisis and enable IS - IS on each interface with the ip router isis command.
  • D、Configure the network net - id command(s) and the is - type level -1- 2 command under routerisis.
  • E、Configure the net system - id and the network net - id commands under routerisis and enable ISIS on each interface with the ip router isis command.

正确答案:A

第10题：

Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）

  • A、TestKingRouter(config)# router ospf 0
  • B、TestKingRouter(config)# router ospf 1
  • C、TestKingRouter(config)# router ospf area 0
  • D、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0
  • E、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0
  • F、TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0

正确答案:B,E

更多相关问题
相关内容