224.0.0.2
224.0.0.5
224.0.0.9
255.255.255.255
第1题:
A. If a packet is sent to a multicast group address, the multicast frame contains the source multicast address.
B. A router does not have to be a member of a multicast group to recei ve multicast data.
C. A router must be a member of a multicast group to send to the group.
D. A router does not have to be a member of a multicast group to send to the group.
E. If a packet is sent to a multicast group address, all members of the multic ast group will receive it.
F. A router must be a member of a multicast group to receive multicast data.
第2题:
A. TestKSwitch(config)# ip route-default 192.168.1.115
B. TestKSwitch(config)# ip default-gateway 192.168.1.115
C. TestKSwitch(config)# ip route 192.168.1.115 0.0.0.0
D. TestKSwitch(config)# ip default-network 192.168.1.115
第3题:
A.224.0.0.2
B.224.0.0.5
C.224.0.0.9
D.255.255.255.255
第4题:
Which configuration command assigns a host route to the CPE workstation address of 192.168.10.1 in a Bridged 1483 network?()
第5题:
A. Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0
B. Router(config)# ip route 0.0.0.0 255.255.255.255 s0
C. Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0
D. Router(config)# ip route 0.0.0.0 0.0.0.0 s0
E. Router(config)# ip route any any e0
第6题:
A. ::/0 is the default route, and ::/128 is the unspecified address.
B. ::/0 is the unicast address, and ::/128 is the anycast address.
C. ::/0 is the anycast address, and ::/128 is the multicast address.
D. ::/0 is the unicast address, and ::/12 8 is the multicast address.
E. ::/0 is the unspecified address, and ::/128 is the multicast address.
F. ::/0 is the anycast address, and ::/128 is the default address.
第7题:
A. LTD(config)# ip route 0.0.0.0 0.0.0.0 192.168.15.36
B. LTD(config)# ip route 0.0.0.0 192.168.15.36 255.255.255.255
C. LTD# ip default-network 0.0.0.0 192.168.15.36 255.255.255.255
D. LTD(config)# ip route 0.0.0.0 0.0.0.0 E0
E. LTD(config)# ip route 0.0.0.0 255.255.255.255 S0
F. LTD(config-router)# ip route 255.255.255.255 0.0.0.0 192.168.15.36
第8题:
A. Use ping and the show ip route command to confirm the timers for each default network resets to 0.
B. Load balancing does not occur over default networks; the second route will only be used for failover.
C. Use an extended ping al ong with repeated show ip route commands to confirm the gateway of last resort address toggles back and forth.
D. Use the traceroute command to an address that is not explicitly in the routing table.
第9题:
A. TK1(config)# ip route 0.0.0.0 0.0.0.0 E0
B. TK1(config)# ip route 0.0.0.0 255.255.255.255 S0
C. TK1(config-interface)# ip route 255.255.255.255 0.0.0.0 192.168.1.21
D. TK1(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.21
E. TK1(config)# ip route 0.0.0.0 192.168.1.21 255.255.255.255
F. TK1# ip default-network 0.0.0.0 192.168.1.21 255.255.255.255
第10题:
Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?()