违法和不良信息举报 联系客服
免费注册 登录

单选题What is the correct configuration of Anycast RP on the loopback interface， assuming a shared anycast address of 10.1.1.1？（）A AB BC CD D

题目
单选题
What is the correct configuration of Anycast RP on the loopback interface， assuming a shared anycast address of 10.1.1.1？（）
A

A

B

B

C

C

D

D

如果没有搜索结果或未解决您的问题，请直接 联系老师 获取答案。
相似问题和答案

第1题：

You would like to configure an Ethernet interface with the following characteristics:Which set of configuration commands accurately completes this task?()

A.A

B.B

C.C

D.D


参考答案：B

第2题：

Which two are correct when configuring an IP address for a Fast Ethernet interface?()

A.set interfaces fe-0/0/0 address 10.1.1.1/24

B.set interfaces fe-0/0/0.0 family inet address 10.1.1.1/24

C.set interfaces fe-0/0/0.0 address 10.1.1.1/24

D.set interfaces fe-0/0/0 unit 0 family inet address 10.1.1.1/24


参考答案：B, D

第3题：

Which two steps are needed when configuring multiple RPs using MSDP within a single PIM domain? ()

A. Configure a non-unique address on the loopback interface for use by the PIM RP.

B. Configure MSDP with the unique address (router ID) as the local address of the peer.

C. Configure MSDP with the non-unique address (router ID) as the local address of the peer.

D. Configure a unique address on the loopback interface, used as the PIM RP.


参考答案：A, B

第4题：

What MSDP solution provides the abiltiy to place the same ip RP address on the loopback of two or more routers？


正确答案:Anycast RP is a useful application of MSDP that configures a multicast sparse mode network to provide for redundancy and load sharing within a single multicast domain. Two or more RPs are configured with the same IP address on loopback interfaces。

第5题：

What is the difference between the IPv6 addresses ::／0 and :: ／128? ()

A. ::/0 is the default route, and ::/128 is the unspecified address.

B. ::/0 is the unicast address, and ::/128 is the anycast address.

C. ::/0 is the anycast address, and ::/128 is the multicast address.

D. ::/0 is the unicast address, and ::/12 8 is the multicast address.

E. ::/0 is the unspecified address, and ::/128 is the multicast address.

F. ::/0 is the anycast address, and ::/128 is the default address.


参考答案：A

第6题：

You are trying to recover from a corrupted flash.Which configuration command configures an IP address of 192.168.1.1／24 on the SRP management interface when the ERX1400 router is at the boot prompt?()

A.A

B.B

C.C

D.D


参考答案：C

第7题：

The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1

A. Automatic 6to4

B. Manually configured tunnel

C. ISATAP

D. GRE


参考答案：A

第8题：

What is the default authentication method on an OSPF interface?()

A.A

B.B

C.C

D.D


参考答案：A

第9题：

Which two of these statements are true of IPv6 address representation?()

A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.

B. A single interface may be assigned multiple IPv6 addresses of any type.

C. Every IPv6 interface contains at least one loopback address.

D. The first 64 bits represent the dynamically created interface ID.

E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.


参考答案：B, C

第10题：

What is the difference between the IPv6 addresses ：：/0 and ：：/128？（）

  • A、：：/0 is the unspecified address， and ：：/128 is the multicast address
  • B、：：/0 is the unicast address， and ：：/128 is the anycast address
  • C、：：/0 is the unicast address， and ：：/128 is the multicast address
  • D、：：/0 is the anycast address， and ：：/128 is the multicast address
  • E、：：/0 is the default route， and ：：/128 is the unspecified address
  • F、：：/0 is the anycast address， and ：：/128 is the default address

正确答案:E

更多相关问题
相关内容