单选题The first step documented in Company.com’s HACMP test plan is to start the cluster manager on the normal service node and verify that HACMP daemons have started with the ’lssrc -g cluster" command.  What daemons MUST show as active in the ’lssrc -g clu

第1题：

Company.com has a cluster with nodes that support "hot swap" adapters. During an upgrade of  The network infrastructure，an additional network adapter has been added to the nodes and configured in AIX.  What is the next step required to add this adapter to HACMP？（）  

• A、 Stop the node.
• B、 Stop the cluster.
• C、 Run autodiscovery.
• D、 Configure the IP adapter.

第2题：

While performing a site survey to document the existing environment before implementing a new HACMP cluster， it was discovered that a port filtering firewall was being used to protect the production system. The plan is to continue using the firewall and add a second firewall to avoid a single point of failure. Each node in the two-node cluster will have all of its network adapters connected to the firewalls， and all connections to the nodes will pass through these firewalls.  What must be considered about HACMP in a firewall environment？（）  

• A、 Firewalls are not supported in a HACMP environment.
• B、 HACMP uses only TCP/IP so firewalls are not relevant.
• C、 Specific ports must be open for HACMP communications.
• D、 Dynamic routing must be used to properly route packets in a firewall-protected environment.

第3题：

An active PowerHA cluster was shutdown from C-SPOC with the "Unmanage Resource Groups" option. Afterthe operation successfully completes， what is the internal state of the cluster manager as shown by the lssrc -ls clstrmgrES command？（）

• A、ST_STABLE
• B、ST_BARRIER
• C、ST_CBARRIER
• D、ST_UNMANAGED

第4题：

A step in the HACMP test plan is to gracefully stop the cluster on a node and to verify that the Shared resources fallover to the standby node. To prepare for this testing step， both nodes in the two-node cluster are in a stable state with the single resource group active on Node ’A’.  Which of the following is the best way to execute this portion of the test plan？（）  

• A、 Execute "lssrc -g cluster stop" on Node ’A’
• B、 Execute "cat /etc//motd >/dev/kmem" on Node ’A’
• C、 Execute "/usr/es/sbin/cluster/utilities/sclstop -gr" on Node ’A’
• D、 Find the pid of cluster manager daemon on Node ’A’ and issue a "kill-9" against the pid

第5题：

An administrator runs clstat on a cluster node and receives the following response： ’Can not get  Cluster Information.’ Which of the following daemons may need to be started in order to correct this problem？（）

• A、 topsvcs
• B、 clinfoES
• C、 snmpinfo
• D、 clsmuxpdES

第6题：

An administrator is reviewing the /tmp/hacmp.out after an unsuccessful fallover and notice that  the event stop_server PROD_DB failed.  Besides manually intervening，what step must be performed to return the cluster to a stable state？（）  

• A、 Recover From HACMP Script Failure.
• B、 Release Locks Set By Dynamic Reconfiguration.
• C、 Rerun HACMP cluster verification and synchronization.
• D、 Restore HACMP configuration Database From Active Configuration.

第7题：

A cluster administrator is performing fallover testing during a scheduled system outage. Node ’A’  Was forced down and eventually rebooted. When Node ’A’ reintegrates into the cluster， the resource group state is offline. No errors are found in reviewing the hacmp.out file.  What could have been done to ensure the resource group was acquired when cluster processing was restarted on Node ’A’？（）

• A、 Nothing，HACMP does not require them automatically.
• B、 Force the remaining nodes down，then reintegrate them all.
• C、 Select reacquire resources after forced down on start menu.
• D、 Create a setting timer to bring the resource group online.

第8题：

A cluster script failed because it was unable to set the hostname， and the Cluster Manager reported the event failure. What must be done prior to sue the "HACMP Problem Determination Tools" -> "Recover From Script Failure" to have the Cluster Manager resume cluster processing？（）  

• A、 Nothing， the "Recover From Script Failure" will correct the issue.
• B、 Disable and re-enable the effected Ethernet adapter by using ifconfig.
• C、 Correct the error by setting the hostname on the effected node from the command line.
• D、 Verify that the clinfo daemon is running prior to executing the "recover from scriptfailure".

第9题：

A cluster node has been started and has not acquired the resources in the resource groups.  Which log file will show the details of any event script processing that has occurred？（）  

• A、 /tmp/hacmp.out
• B、 /tmp/clstrmgr.debug
• C、 /usr/es/adm/cluster.log
• D、 /var/adm/hacmp/hacmp.out

第10题：

Company.com has installed HACMP and is configuring a three-node cluster. One of the Applications  uses the AIX hostname as a key for authorization to execute on the specific computer. The application vendor was contacted and consented to having multiple copies of the application but required that only one application be active at any one point in time.  How can the AIX host name dependency be managed in an HACMP environment.（）  

• A、 It cannot be managed because the application will not work properly with HACMP.
• B、 The application start and stop script for the application can manage the hostname.
• C、 HACMP will require customization to correctly manage a change in the hostname since it is tied to the primary network adapter.
• D、 HACMP will have to be restarted if the hostname is changed. This can be done with customization in the node_up and node_down event scripts.