An administrator has just installed a new NIC into the serve

题目
单选题
An administrator has just installed a new NIC into the server. The system POSTs fine and the NIC is recognized by the OS, but it does not receive an IP address. Which of the following is the MOST likely cause of this?()
A

The NIC is not on the HCL.

B

The driver is incorrect on the server.

C

The patch cable has not been seated properly.

D

The NIC is not seated properly.

参考答案和解析
正确答案: C
解析: 暂无解析
如果没有搜索结果或未解决您的问题,请直接 联系老师 获取答案。
相似问题和答案

第1题:

An administrator has just installed a new NIC into the server. The system POSTs fine and the NIC is recognized by the OS, but it does not receive an IP address. Which of the following is the MOST likely cause of this?()

A. The NIC is not on the HCL.

B. The driver is incorrect on the server.

C. The patch cable has not been seated properly.

D. The NIC is not seated properly.


参考答案:C

第2题:

An administrator just installed a new RAID controller card into a server. The firmware is current for the controller card. When the server is powered up the administrator notices that the RAID controller card is not recognized during POST. Which of the following is the cause of the problem?()

  • A、The hard drives were not plugged into the server correctly.
  • B、The controller driver is outdated and needs to be updated from the OEMs website.
  • C、The firmware for the server is too old and does not support the new RAID controller card.
  • D、The cable from the controller to the hard drive backplane is not connected.

正确答案:C

第3题:

The network administrator has just finished installing a new 10/100/1000 switch, but receives reports from the server administrator that servers connected to the new switch seem to be experiencing slow LAN connections. The network administrator checks the port connecting the new switch to the core switch and sees the following information:Which of the following is the MOST likely cause of the slow connections?()

A. The servers have not had VLAN tagging enabled on their NICs.

B. Speed and duplex have not been set.

C. VLAN tagging was not set on the trunk.

D. The servers have been connected with CAT5 cable.


参考答案:B

第4题:

A new server was installed for the purpose of monitoring network traffic. The network has been configured in such a way that all traffic will be mirrored out the port this server is connected to. When reviewing the network traffic logs on the server only traffic destined to the server is listed in the logs. Which of the following is preventing the server from seeing all network traffic?()

  • A、NIC filtering is enabled.
  • B、Port security is configured.
  • C、NIC is not in promiscuous mode.
  • D、NIC is in promiscuous mode.

正确答案:C

第5题:

An administrator has just installed a new NIC into the server. The system POSTs fine and the NIC is recognized by the OS, but it does not receive an IP address. Which of the following is the MOST likely cause of this?()

  • A、The NIC is not on the HCL.
  • B、The driver is incorrect on the server.
  • C、The patch cable has not been seated properly.
  • D、The NIC is not seated properly.

正确答案:C

第6题:

The technician has suspicions that a browser has been hijacked. Which of the following should the technician look for in this situation?()

  • A、A new default gateway has been setup.
  • B、A new Internet shortcut has been added.
  • C、A new web browser has been installed and is now the default.
  • D、A proxy server has been enabled.

正确答案:D

第7题:

A technician has installed an additional NIC on a server. Which of the following can now be set up?()

  • A、Teaming
  • B、VLANs
  • C、Port forwarding
  • D、Full duplex

正确答案:A

第8题:

A technician has just finished installing a new NIC into a customer’s desktop. Which of thefollowing should the technician do NEXT?()

A. Perform a full system backup.

B. Follow up with the customer, verifying satisfaction.

C. Ask their manager to contact the customer.

D. Perform a complimentary virus scan.


参考答案:B

第9题:

A technician has just installed a new power supply into a desktop computer and now the computer will not turn on. Which of the following is the MOST likely cause?()

  • A、The voltage selector switch on the power supply is set incorrectly.
  • B、The 3.3v power line is connected to the wrong input on the motherboard.
  • C、The new power supply voltage rating is too high.
  • D、The 12v power cord is installed incorrectly.

正确答案:A

第10题:

The administrator has just installed a new memory module into the server. Now, the server is not showing the new memory. Which of the following should the administrator perform FIRST?()

  • A、System reboot
  • B、Reseat the memory
  • C、Install the latest firmware
  • D、Install the latest driver

正确答案:B

更多相关问题