The switch will ignore VTP summary advertisements.
The switch will forward VTP summary advertisements.
The switch will process VTP summary advertisements.
The switch will originate VTP summary advertisements.
The switch will create, modify and delete VLANs for the entire VTP domain.
第1题:
You need to configure an 802.1Q link on a Ezonexam switch. Which commands, when used together, would do this? (Select two answer choices)
A. Switch(vlan) mode trunk
B. Switch(config) switchport access mode trunk
C. Switch(config-if) switchport mode trunk
D. Switch(config-if) switchport trunk encapsulation dot1q
E. Switch(config) switchport access mode 1
F. Switch(vlan) trunk encapsulation dot1q
第2题:
阅读以下说明,回答问题1~3,将答案填入对应的解答栏内。
随着越来越多的机构为任务关键型通信寻求经济利益,高可靠性变得日益关键。网络通信注意力集中在提供一种7×24小时都可用的网络架构上。可是,最大的挑战之一不是来自于网络架构,而是来自于用户级的工作站和网络设备。
热备份路由选择协议(HSRP)为IP碉络提供了容错和增强的路由选择功能。如图5-1就是一个典型的HSRP网络的实现。
两台多层交换机的配置如下,解析配置文件中部分语句的意义。
***Switch1的交换引擎的配置***
Switch1>(enable)set vtp mode server (1)
Switch1>(enable)set vtp domain Core Net //设置VTP域名
Switch1>(enable)set vlan 10 name CaiWuBu //创建VLAN 10
Switch1>(enable)set vlan 20 name XingZheng //创建VLAN 20
Switch1>(enable)set trunk 1/1 on dotlq 1-1005 (2)
Switch1 (2) (enable)set spantree root 1-40 dia 4 (3)
Switch1 (3) (enable)set spantree portfast 1/1-2 enable (4)
Switch1 (4) (enable)set spantree uplinkfast enable (5)
……(略)
***Switch1的路由引擎的配置***
Switch1(config)enable secret test //设定登录口令
Switch1(config)line vty 0 4 //进入VTY模式
Switch1(config-line)login
Switch1(config-line)password test //设用户级口令
……(略)
Switch1(config-if)interface vlan 10 //进入虚接HVLAN 10
Switch1(config-if)ip address 192.168.180.60 255.255.255.192
//设定IP地址
Switch1(config-if)no shutdown //开启端口
Switch1(config-if)standby 10 ip 192.168.180.62 (6)
Switch1(config-if)standby 10 priority 110 (7)
Switch1(config-if)standby 10 preempt (8)
Switch1(config-if)interfacevlan 20 //进入虚接口VLAN 20
Switch1(config-if)ip address 192.168.180.124 255.255.255.192
//设定IP地址
Switch1(config-if)no shutdown //开启端口
Switch1(config-if)standby 20 ip 192.168.180.126
Switch1(config-if)standby 20 priority 110
Switch1(config-if)standby 20 preempt
……(略)
***Switch2的交换引擎的配置***
Switch2>(enable)set vtp mode server
Switch2>(enable)set vtp domain Core_Net //设置VTP域名
Switch2>(enable)set vlan 10 name CaiWuBu //创建VLAN 10
Switch2>(enable)set vlan 20 name XingZheng //创建VLAN 20
Switch2>(enable)set trunk 1/1 on dotlq 1-1005
Switch2>(enable)set spantree secondary root 1-40 dia 4
……(略)
***Switch2的路由引擎的配置**+
Switch2(config)enable secret test //设定登录口令
……(略)
Switch2(config-if)interface vlan 10 //进入虚接口VLAN 10
Switch2(config-if)ip address 192.168.180.61 255.255.255.192
//设定IP地址
Switch2(config-if)no shutdown //开启端口
Switch2(config-if)standby 10 ip 192.168.180.62
Switch2(config-if)standby 10 priority 100
Switch2(config-if)standby 10 preempt
Switch2(config-if)interface vlan 20 //进入虚接口VLAN 20
Switch2(config-if)ip address 192.168.180.125 255.255.255.192
Switch2(config-if)no shutdown
Switch2(config-if)standby 20 ip 192.168.180.126
Switch2(config-if)standby 20 priority 100
Switch2(config-if)standby 20 preempt
……(略)
第3题:
● 交换机命令switch(config)# vtp pruning的作用是 (59) 。
(59)
A. 指定交换机的工作模式
B. 启用VTP 静态修剪
C. 指定VTP 域名
D. 启用VTP 动态修剪
第4题:
f a Cisco switch is configured with VTPv1 in transparent mode, what is done with received VTP advertisements?()
第5题:
An administrator is unsuccessful in adding VLAN 50 to aswitch. While troubleshooting the problem, the administrator views the output of the show vtp status command, which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database?()
A. Switch(config-if)# switchport access vlan 50
B. Switch(vlan)# vtp server
C. Switch(config)# config-revision 20
D. Switch(config)# vlan 50 name Tech
E. Switch(vlan)# vlan 50
F. Switch(vlan)# switchport trunk vlan 50
第6题:
The Ezonexam network administrator has issued the "VTP password ezonexam" command on a Cisco device. What is the purpose of this command?
A.It allows two VTP servers to exists in the same domain, each configured with different passwords
B.It is the password required when promoting a switch from VTP client mode to VTP server mode
C.It is used to access the VTP server to make changes to the VTP configuration
D.It is used to validate the sources of VTP advertisements sent between switches
E.None of the above
第7题:
You are bringing up a new Ezonexam switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?
A.Switch(config)# switchport trunk encapsulation isl
B.Switch(config)# switchport trunk encapsulation ietf
C.Switch(config-if)# switchport trunk encapsulation isl
D.Switch(config-if)# switchport trunk encapsulation ietf
E.Switch(config-if)# switchport trunk encapsulation dot1q
第8题:
交换机命令switch(config)# vtp prLming的作用是______。
A.指定交换机的工作模式
B.启用VTP静态修剪
C.指定VTP域名
D.启用VTP动态修剪
第9题:
A.if a switch that is configured to operate in client mode cannot access a VTP server,then the switch reverts to transparent mode.
B.The local vlan configuration is updated only when an update that has a higher configuration revision number is received.
C.Vtp advertisements are not forwarded to neighboring switches that are configured in vtp transparent mode.
D.When switches in vtp client mode are rebooted,they send a vtp advertisement request to the vtp servers.
E.Vtp client is the default vtp mode
F.On switches that are configured to operate in client mode ,vlans can be created,deleted,or renamed locally
第10题:
What action should you execute if you wanted to enable VTP pruning on your entire management domain?()