Hydraulically, servo-operated, automatic, change over valves

题目
单选题
Hydraulically, servo-operated, automatic, change over valves, utilized in a two ram hydraulic steering gear, serve to()
A

allow an alternate main pump to start in the fully loaded condition thus developing immediate full torque

B

prevent either main pump from being hydraulically motored when idle by cross pressure flow

C

prevent both units from operating simultaneously which could result in doubling the flow of oil and pressure leading to over pressurization of the system

D

all of the above

如果没有搜索结果或未解决您的问题,请直接 联系老师 获取答案。
相似问题和答案

第1题:

What must be handed over to relieving Engineer Officer at transition of change command?


正确答案:If possible, the condition and mode of operation of automatic boiler controls such as flame safeguard control systems, limit control system, combustion control system, fuel-supply control systems, and other equipment related to the operation of steam boilers; and potentially adverse conditions due to bad weather, ice, contaminated or shallow water; any special modes of operation dictated by equipment failure or adverse ship conditions; reports of engine-room ratings relating to their assigned duties; the availability of fire-fighting appliances; the state of completion of Engine-Room Log.

第2题:

The term () linguistics may be defined as a way of referring to the approach which studies language change over various periods of time and at various historical stages.

Asynchronic

Bdiachronic

Ccomparative

Dhistorical comparative


B

第3题:

Over the past 20 years, the Internet has helped change our world in way or another for the better.

A. anyB. one C. everyD. either


正确答案:B

第4题:

You use the Memory Advisor to tune the memory structures of your database. What is the prerequisite to use the Memory Advisor?()

  • A、 The database must be in the ARCHIVELOG mode.
  • B、 The automatic memory tuning must be enabled.
  • C、 The change tracking feature must be enabled.
  • D、 The automatic memory tuning must be disabled.

正确答案:D

第5题:

Which of the following procedures best explains how to enable the NIS name resolution to take precedence over DNS on a system-wide basis?()

  • A、 Add the following line to /etc/netsvc.conf: hosts = nis,bind,local 
  • B、 edit /etc/netsvc.conf to add the following: process /full/path/of/process /{ hosts = local,nis,dns} 
  • C、 In an NIS and DNS environment, NIS takes precedence over DNS in this environment resulting in no change 
  • D、 Change the NSORDER environment variable 

正确答案:A

第6题:

The “Port-Off-Stbd” selector switch on an autopilot steering stand is used to ______.

A.change from hand electric steering to automatic gyro

B.change over one steering system to the other

C.change over hand electric steering to non-follow-up

D.change over the port to the starboard bow thruster


正确答案:B

第7题:

Which of the following is the FIRST course of action before implementing a change to a server?()

  • A、 Survey users to get their response to the potential server change.
  • B、 The change should be approved by management.
  • C、 Switch over to the alternate site so users are not affected.
  • D、 Implement RAID so the server does not go offline.

正确答案:B

第8题:

the obvious change over the past decades is the decline of the authority of the roman catholic church. ()


参考答案:正确

第9题:

What will happen to associated preventive maintenance (PM) records when an asset is decommissioned?()

  • A、There is no automatic method to change the PM(s) status to INACTIVE
  • B、The PM(s) will become in INACTIVE if 'Change the Status of All Associated PM(s) to Inactive?' is checked while decommissioning the asset
  • C、The only way to change the status of the PM(s) to INACTIVE is to remove the assets from the PM(s) and then change the status of the PM(s) to INACTIVE
  • D、If the 'Change the Status of All Associated PM(s) to Inactive?' is not selected during decommissioning, the PM(s) status will remain ACTIVE; however, work order cannot be generated from the PM having a decommissioned asset

正确答案:B

第10题:

单选题
You use the Memory Advisor to tune the memory structures of your database. What is the prerequisite to use the Memory Advisor?()
A

 The database must be in the ARCHIVELOG mode.

B

 The automatic memory tuning must be enabled.

C

 The change tracking feature must be enabled.

D

 The automatic memory tuning must be disabled.


正确答案: D
解析: 暂无解析

更多相关问题