Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?()
第1题:
A.show interfaces queue ge-0/0/0
B.show statistics queue detail
C.show interfaces ge-0/0/0 statistics extensive
D.monitor interface ge-0/0/0 queue
第2题:
A. show interfaces serial 0/0
B. show running-config
C. show version
D. show controllers serial 0/0
E. show ip interface
F. show line serial 0/0
第3题:
An administrator issues the show ip interface s0/0 command and the output displays that interface Serial0/0 is up, line protocol is up.
What does "line protocol is up" specifically indicate about the interface?
A.The cable is attached properly.
B.CDP has discovered the connected device.
C.Keepalives are being received on the interface.
D.A carrier detect signal has been received from the connected device.
E.IP is correctly configured on the interface.
第4题:
A. Serial0/1 is up, line protocol is down
B. Serial0/1 is down, line protocol is down
C. Serial0/1 is up, line protocol is up
D. Serial0/1 is administratively down, line protocol is down
第5题:
There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers:From your observations of the above exhibit, what is the underlying cause of the problem?()
A. The loopback is not set.
B. The serial cable is faulty.
C. The subnet mask is not configured properly.
D. The IP address is not configured properly.
E. The Layer 2 frame types are not compatible.
F. The keepalive setting is not configured properly.
第6题:
A. show interfaces alarms
B. show interfaces terse
C. show alarms extensive
D. show interfaces extensive
第7题:
While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?()
A. Serial 0 is up, line protocol is up
B. Serial 0 is up, line protocol is down
C. Serial 0 is down, line protocol is down
D. Serial 0 is down, line protocol is up
E. Serial 0 is administratively down, line protocol is down
F. Serial 0 is administratively down, line protocol is up
第8题:
A.monitor interface ge-0/0/0 queue
B.show interfaces queue ge-0/0/0
C.show interfaces ge-0/0/0 statistics extensive
D.show statistics queue detail
第9题:
Part of the configuration files for routers testking1 and testking2 are displayed below:If you were to enter the "show interface serial 0" command on router testking1,which of the following will be displayed?()
A. Serial 0 is down, line protocol is down
B. Serial 0 is up, line protocol is up
C. Open: IPCP, CDPCP
D. LCP closed
E. LCP open
第10题:
Refer to the exhibit.The network administrator is in acampus building distant from Building B.WANRouter is hosting a newly installed WAN link on interface S0/0.The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface.How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner?()
A.Telnet to WANRouter and execute the command show interfaces S0/0
B.Telnet to WANRouter and execute the commandshow processes S0/0
C.Telnet to WANRouter and execute the command show running-configuration
D.Telnet to WANRouter and execute the command show controller S0/0
E.Physically examine the cable between WANRouter S0/0 and the DCE.
F.Establish a console sessionon WANRouter and execute the command show interfaces S0/0